Lock Mechanism Replacement - Andersen Windows

16 Pages·2015·2.71 MB·English

by  Andersen Windows

Lock Mechanism Replacement
for Andersen® A-Series Inswing & Outswing; 400 Series Frenchwood®
Hinged Inswing & Outswing Patio Doors and 400 Series Frenchwood®
Hinged Inswing & Outswing Patio Doors with Stormwatch® Protection
Thank you for choosing Andersen. / Gracias por elegir Andersen.
For questions call 1-888-888-7020.
Due to ongoing product changes, updated test results and/or industry best practices, this installation procedure may change over time. For updated
installation guides, removal instructions and/or additional installation information, visit andersenwindows.com/installation.
Contact local authorities or waste management companies for proper recycling and/or disposal of removed window or patio door.
Please leave this guide with building owner.
▶ Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Use caution when working at elevated heights and around unit
openings. Follow manufacturers’ instructions for ladders and/or
scaffolding. Failure to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage. Incorrect installation may affect egress and home security. Follow instruction
guide to make sure hardware is installed correctly.
Incorrect installation may affect egress and home security. Follow instruction
guide to make sure hardware is installed correctly.
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©1996-2015 Andersen Corporation. All rights reserved. 0005233 BD-00 Revised 07/08/15
Parts Included Panel Identification
(1) Instruction Guide Astragal
(1) Passive OR Active Lock Mechanism
(1) Inswing Blocker Assembly
(1) Outswing Blocker Assembly

Tools & Supplies
• Safety Glasses
• Hex Wrench for Handle Set Screw
• Phillips Screwdriver
• Flat Blade Screwdriver
• Torx Screwdriver
• Utility Knife
Active Panel Passive Panel Active Panel
• Locking Pliers
(Operating Panel (Operating Panel with (Hinged or
• Hammer
most commonly Astragal attached) Operating Panel)
used)
This instruction guide includes instructions for replacing either the Active Panel Lock Mechanism or the Passive
Panel Lock Mechanisms. For Passive Panel Lock Mechanism Replacement proceed below. For Active Panel
Lock Mechanism Replacement go to Page 6.
Lock Mechanism Replacement - Passive Panel
1. Remove Trim Set
Support Handles and Escutcheon Plates when
Exterior Escutcheon Plate
removing bolts to avoid dropping/damaging hardware.
• Loosen Set Screw on underside of
Exterior Handle
Exterior Handle to remove Interior
Interior
and Exterior Handle. Escutcheon
Set Screw Plate
• Remove Escutcheon Plate Bolts and
Interior Escutcheon Plate.
• Remove Exterior Escutcheon Plate Hex Wrench
and Gasket.
Gasket
Escutcheon Plate Bolts Interior Handle
2
2. Remove Hardware from Passive Panel
• Remove Hook Bolt Receivers, Strike
Plate, and Dead Bolt Latch Receiver/
Blocker using Phillips screwdriver.
Hook Bolt Hook Bolt
Receiver Receiver
Hook Bolt Receiver with Hook Bolt Receiver with
Machine Screws Machine Screws
(units over 8" tall only) (units over 8" tall only)
Wood screws used for all Wood screws used for all
other locations. other locations.
Strike Plate
Strike Plate
Dead Bolt Latch
Dead Bolt Latch
Receiver/Blocker
Receiver/Blocker
(underneath
(underneath
Strike Plate)
Strike Plate)
Hook Bolt
Receiver Hook Bolt
Receiver
Passive Panel Passive Panel
A-Series Hinged Inswing, 400 Series A-Series Hinged Outswing, 400 Series
Frenchwood® Hinged Inswing and 400 Series Frenchwood® Hinged Outswing and 400
Frenchwood® Hinged Inswing Patio Doors Series Frenchwood® Hinged Outswing
with Stormwatch® Protection Patio Doors with Stormwatch® Protection
3. Remove Astragal
Utility Knife
Utility Knife
Interior View
It may be necessary to break paint Interior View
or varnish seal between Astragal
Trim Strip and door panel before
removing Astragal. Break seal
using a sharp utility knife.
Astragal Astragal
• Pull outwards to remove Astragal. If
Astragal does not come out lightly,
break paint or varnish seal between
Exterior View Exterior View
Astragal Trim Strip and panel using a
Passive Panel Passive Panel
sharp utility knife.
A-Series Hinged Inswing, 400 A-Series Hinged Outswing, 400
Series Frenchwood® Hinged Inswing Series Frenchwood® Hinged Outswing
and 400 Series Frenchwood® and 400 Series Frenchwood®
Hinged Inswing Patio Doors with Hinged Outswing Patio Doors with
Stormwatch® Protection Stormwatch® Protection
3
4. Remove Existing Lock Mechanism
• Remove and retain screws holding
Lock Mechanism.
• Remove Lock Mechanism.
Lock Mechanism
5. Attach Blocker to Replacement Lock Mechanism
• Identify proper Blocker to use.
Properly dispose of unused Blocker.
• Separate Blocker Cap from Blocker
Pin using a pliers.
Blocker
• Tap Blocker Pin into bottom of Lock Frenchwood® Hinged Patio Door
until fully seated using a hammer.
• Snap Blocker Cap over Blocker Pin.
Blocker
Frenchwood® Outswing Patio Door
Locking Pliers
Blocker Pin
Blocker Cap
Hammer
Blocker Pin
Blocker Pin Hole
4
6. Install Replacement Passive Lock Mechanism
• Insert Lock Mechanism into
door panel and secure using
or
appropriate size screws.
Use #8 x 5" Torx Head Screw
here for 400 Series Frenchwood
Hinged Inswing and Outswing
Patio Doors with Stormwatch®
Protection Only
#8 x 1-1/2" Screw
(Frenchwood® Hinged Inswing)
#8 x 2" Screw
(Frenchwood® Hinged Outswing)
Use #8 x 5" Torx Head Screw
here for 400 Series Frenchwood
Hinged Inswing and Outswing
Patio Doors with Stormwatch®
Protection Only
or
Passive Lock Mechanism
7. Reapply Astragal, Hardware and Trimset
• Reapply Astragal, Hardware and Trimset
reversing procedure in steps 1, 2 and 3.
5
Lock Mechanism Replacement - Active Panel
1. Remove Trimset
Support Handles and Escutcheon Plates when
removing bolts to avoid dropping/damaging hardware.
• Loosen Set Screw on underside Exterior Escutcheon Plate
of Exterior Handle to remove Cylinder
Interior and Exterior Handle.
Lock Actuator
• Remove Escutcheon Plate Bolts Exterior Handle
and Interior Escutcheon Plate. Limiting Plate
• Remove Exterior Escutcheon
Cylinder
Plate and Gasket. Set Screw Mounting
Bolts
• Remove Cylinder Mounting Bolts,
Limiting Plate, Lock Actuator, and
Hex Wrench
Cylinder.
Gasket
Interior Escutcheon Plate
Escutcheon Plate Bolts Interior Handle
2. Remove Lock Mechanism
• Note orientation of Latch on Lock
Mechanism. Lock position will be
addressed in Step 5.
• Remove and retain all screws along
length of Lock Mechanism.
• Pull Lock Mechanism out of panel.
Latch
Lock Mechanism
Lock Mechanism
(removed)
6
3. Install Replacement Lock Mechanism
#8 x 5" Torx Head Screw
• Insert Lock Mechanism into door panel
(400 Series Frenchwood®
and secure using appropriate size screws. Hinged Inswing and
Outswing)
All screws unless otherwise noted are:
#8 x 1-1/2" for 400 Series Frenchwood® Hinged Inswing
or
#8 x 2" for 400 Series Frenchwood® Hinged Outswing
or
Use #8 x 5" Torx Head
Screw here for 400
Series Frenchwood
Hinged Inswing and
Outswing Patio Doors
with Stormwatch®
Protection Only
3 Point Active 5 Point Active Lock 4 Point Active Lock 6 Point Active Lock
Lock Mechanism Mechanism Mechanism Mechanism
Active/Passive or Active Single Doors Active/Passive or
Passive/Active Over 8’ Tall Only Passive/Active
Doors Only Doors Over 8’ Tall Only

Use #8 x 5" Torx Head
Screw here for 400
Series Frenchwood
Hinged Inswing and
Outswing Patio Doors
with Stormwatch®
Protection Only
or
#8 x 5" Torx Head Screw
(400 Series Frenchwood® Hinged Inswing and Outswing)
7
4. Install Trim Set
• Reinstall Trim Set by reversing procedure in Step 1.
5. Check Handing of Latch and Operation of Lock Mechanism
• Check position of Latch. If Latch needs to be reversed,
proceed with bullets below.
• Insert a 1/8" flat blade screwdriver into Latch Reversal
Hole until it bottoms out.
• Apply downward pressure on screwdriver handle while
pulling Latch up and out, as shown.
• Remove screwdriver from Latch Reversal Hole.
Latch Reversal Hole
Latch
Flat Blade Screwdriver
Up
• Grasp Latch, pull outwards slightly, and rotate 180°.
Position Latch so that sloped portion contacts Latch
Receiver first.
• Push Latch back into Lock Mechanism Housing.
Latch Latch
Lock
Mechanism
▶ Lock mechanism replacement procedure is complete. Housing
8
Reemplazo de mecanismo de cerrojo
para puertas para patio de los tipos: Andersen® de la serie A
de batiente hacia el interior y el exterior; Frenchwood®
con bisagras de batiente hacia el interior y el exterior de la serie 400; Frenchwood®
con bisagras de batiente hacia el interior y el exterior de la serie 400 con protección Stormwatch®
Gracias por elegir Andersen.
Si tiene alguna pregunta llame al 1-888-888-7020.
Debido a los cambios continuos de los productos, los resultados de los exámenes actualizados y las mejores prácticas de la industria, este procedimiento de
instalación se puede cambiar con el tiempo. Para actualizar las guías de instalación, instrucciones de eliminación e información de instalación adicional, visite
andersenwindows.com/installation.
Póngase en contacto con las autoridades locales o con empresas de gestión de residuos para reciclaje y desecho adecuados de la ventana o puerta del patio eliminadas.
Deje esta guía con el dueño de la construcción.
▶ Lea completamente la guía antes de comenzar la instalación. Lea y respete todas las advertencias y precauciones durante la instalación de la unidad.
▶ Consulte los códigos locales de construcción para identificar y confirmar que se cumplan los requisitos del código de construcción.

Sea cauteloso al trabajar en lugares elevados y cerca de las
aberturas de la unidad. Siga las instrucciones del fabricante
para el uso de escaleras y/o andamios. Si no lo hiciera, podrían
producirse lesiones o la muerte.
Siga las instrucciones del fabricante para el uso de herramientas
eléctricas o manuales. Utilice siempre gafas de seguridad. Si no
lo hiciera, podrían producirse lesiones y/o daños al producto. Su incorrecta instalación puede afectar la salida y la seguridad del hogar. Siga
la guía de instrucciones para asegurarse de que los herrajes estén instalados
correctamente.
“Andersen” y las demás marcas que aparezcan son marcas registradas de Andersen Corporation. ©2009-2015 Andersen Corporation. Todos los derechos reservados. 0005233 BD-00 Revised 04/01/15
Piezas incluidas Identificación del panel
(1) Guía de instrucciones Astrágalo
(1) Mecanismo de cerrojo para panel fijo O de apertura
(1) Conjunto bloqueador de batiente hacia el interior
(1) Conjunto bloqueador de batiente hacia el exterior
Herramientas y suministros
• Lentes de seguridad
• Llave hexagonal para tornillo de fijación de la manija
• Destornillador Phillips
• Destornillador de punta plana
• Destornillador Torx
• Navaja
Panel de Panel fijo Panel de
• Pinzas de presión
apertura (panel operativo con apertura
• Martillo
(panel operativo astrágalo incorporado) (panel con
usado con más bisagra u
frecuencia) operativo)
Esta guía incluye instrucciones para reemplazar el mecanismo de cerrojo del panel de apertura o del panel fijo.
Para ver cómo reemplazar el mecanismo de cerrojo del panel fijo, siga leyendo a continuación. Para ver cómo
reemplazar el mecanismo de cerrojo del panel de apertura, consulte la página 6.
Reemplazo del mecanismo de cerrojo - panel fijo
1. Retirar el kit de accesorios
Al extraer los pernos, sostenga las manijas y los
Escudete exterior
escudetes para que no se caigan ni dañen.
• Afloje el tornillo de fijación en el lado Manija
inferior de la manija exterior para exterior
Escudete interior
extraer la manija interior y exterior.
Tornillo de
• Extraiga los pernos del escudete y el
fijación
escudete interior.
Llave
• Retire el escudete exterior y la junta.
hexagonal
Junta
Pernos del escudete Manija interior
10