Interior Design Specifications - AEM - Aerospace Engineering and

501 Pages·2010·2.02 MB·English

AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
SECTION 00 01 10
TABLE OFCONTENTS
DIVISION00–PROCUREMENTANDCONTRACTINGREQUIREMENTS
000110 TableofContents
DIVISION22–PLUMBING
220500 PlumbingMaterials&Methods
220517 SleevesandSleeveSealsforPlumbingPiping
220519 PlumbingMeters&Gauges
220523 PlumbingValves
220529 PlumbingHangers&Supports
220553 PlumbingIdentification
220719 PlumbingPipingInsulation
221116 DomesticWaterPiping
221316 SanitaryWaste&VentPiping
221413 StormDrainagePiping
223000 PlumbingSpecialties
224000 PlumbingFixtures
DIVISION23–HEATING,VENTILATING,ANDAIR-CONDITIONING(HVAC)
230500 HVACMaterials&Methods
230513 HVACMotors
230517 HVACSleeves&SleeveSeals
230519 HVACMeters&Gages
230523 HVACGeneralDutyValves
230529 HVACHangers&Supports
230548 HVACVibrationAndSeismicControls
230553 HVACIdentification
230593 Testing,Adjusting,&Balancing
230713 DuctInsulation
230716 HVACEquipmentInsulation
230719 HVACPipeInsulation
230900 Instrumentation&ControlForHVAC
232113 HydronicPiping
232123 HydronicPumps
232213 Steam&CondensatePiping
232500 HVACWaterTreatment
233113 MetalDuctwork
233300 DuctworkAccessories
233416 CentrifugalFans
233600 AirTerminalUnits
TABLEOFCONTENTS (UofMProjectNo’s.1-266-09-1477) 000110-1
(DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
233713 Diffusers,RegistersandGrilles
233723 HVACGravityVentilators
234100 ParticulateAirFiltration
235700 HeatExchangersforHVAC
237314 FactoryCustomAirHandlingUnits
238239 UnitHeaters
DIVISION26-ELECTRICAL
260500 CommonWorkResultsforElectrical
260019 Low-VoltageElectricalPowerConductorsandCables
260526 GroundingandBondingforElectricalSystems
260529 HangersandSupportsforElectricalSystems
260533 RacewayandBoxesforElectricalSystems
260536 CableTraysforElectricalSystems
260553 IdentificationforElectricalSystems
260923 LightingControlDevices
262200 Low-VoltageTransformers
262416 Panelboards
262726 WiringDevices
265100 InteriorLighting
DIVISION27–COMMUNICATION
NOTUSED
DIVISION28–ELECTRONICSAFETYANDSECURITY
283111 Digital,AddressableFireAlarmSystem
ENDOFDOCUMENT
TABLEOFCONTENTS (UofMProjectNo’s.1-266-09-1477) 000110-2
(DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
SECTION 22 0500
PLUMBINGMATERIALSAND METHODS
PART 1- GENERAL
1.1 RELATEDDOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary
ConditionsandDivision1SpecificationSections,applytothisSection.
1.2 SUMMARY
A. ThisSectionincludesthefollowing:
1. Buildingserviceoutages.
2. Electricalrequirementsforplumbingequipment.
3. Weldingrequirements.
4. Firesafetyprecautions
5. Plumbingsystemscommissioning
6. Pipingmaterialsandinstallationinstructionscommontomostpipingsystems.
7. Transitionfittings.
8. Dielectricfittings.
9. Escutcheons.
10. Grout.
11. CuttingandPatching
12. PlumbingDemolition
13. Equipmentinstallationrequirementscommontoequipmentsections.
14. Paintingandfinishing.
15. Concretebases.
16. Supportsandanchorages.
1.3 DEFINITIONS
A. Finished Spaces: Spaces other than mechanical and electrical equipment rooms, furred
spaces, pipe and duct shafts, unheated spaces immediately below roof, spaces above
ceilings,unexcavatedspaces,crawlspaces,andtunnels.
B. Exposed, Interior Installations: Exposed to view indoors. Examples include finished
occupiedspacesandmechanicalequipmentrooms.
C. Exposed, Exterior Installations: Exposedto view outdoors or subject to outdoor ambient
temperaturesandweatherconditions. Examplesincluderooftoplocations.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-1
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
D. Concealed, Interior Installations: Concealed from view and protected from physical
contactbybuildingoccupants. Examplesincludeaboveceilingsandinductshafts.
E. Concealed, Exterior Installations: Concealed from view and protected from weather
conditions and physical contact by building occupants but subject to outdoor ambient
temperatures. Examplesincludeinstallationswithinunheatedshelters.
F. Thefollowingareindustryabbreviationsforplasticmaterials:
1. ABS: Acrylonitrile-butadiene-styreneplastic.
2. CPVC: Chlorinatedpolyvinylchlorideplastic.
3. PE: Polyethyleneplastic.
4. PVC: Polyvinylchlorideplastic.
G. Thefollowingareindustryabbreviationsforrubbermaterials:
1. EPDM: Ethylene-propylene-dieneterpolymerrubber.
2. NBR: Acrylonitrile-butadienerubber.
1.4 SUBMITTALS
A. ProductData: Forthefollowing:
1. Transitionfittings.
2. Dielectricfittings.
3. Mechanicalsleeveseals.
4. Escutcheons.
B. Weldingcertificates.
1.5 QUALITYASSURANCE
A. ProductStandards:
1. RefertoDivision1.
2. Where products are specified by manufacturer, brand name or catalog number,
this establishes the standard of quality and style of the product to be provided
undertheContract,unlessachangeinqualityorstyleisapprovedbyOwner.
3. All Contractor-furnished equipment, including its component parts, shall be the
current standard products of the manufacturer in order to insure prompt and
continuingserviceandreplacementofparts.
4. Where 2 or more units of the same class of equipment are required, these units
shall be the products of a single manufacturer; however, the component parts of
theequipmentneednotbetheproductofthesamemanufacturer.
B. ReferencedStandards:
1. The following are names of technical and trade organizations, together with the
corresponding acronyms, used in this Specification when citing specific
standardspublishedbytheseorganizations:
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-2
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
a. Air-ConditioningandRefrigerationInstitute(ARI)
b. AmericanConcreteInstitute
c. AmericanConferenceofGovernmentalIndustrialHygienists
d. AmericanGasAssociation(AGA)
e. AmericanInstituteofSteelConstruction
f. AmericanNationalStandardsInstitute(ANSI)
g. American Society of Heating, Refrigeration and Air Conditioning
Engineers
h. AmericanSocietyofMechanicalEngineers(ASME)
i. AmericanSocietyforTestingMaterials(ASTM)
j. AmericanWaterWorksAssociation(AWWA)
k. AmericanWeldingSociety
l. ANSICodeforPowerPipingB31.1
m. Hydraulic Institute Standards for Centrifugal, Rotary and Reciprocating
Pumps
n. InstituteofElectricalandElectronicEngineers
o. NationalBureauofStandards
p. NationalCommercialandIndustrialInsulationStandards
q. NationalElectricalManufacturersAssociation(NEMA)
r. NationalElectricCode(NEC)
s. NationalSafetyCodeforMechanicalRefrigeration
t. OccupationalSafetyandHealthOrganization(OSHA)
u. TubularExchangerManufacturersAssociation(TEMA)
v. UnderwritersLaboratories(UL)
2. Where a reference standard is cited in this Specification, the subject to which it
applies (equipment, material or work) shall be in compliance with the most
recenteditionofthatstandard.
3. None of the above, however, shall be construed as relieving Contractor from
complying with any requirement in this Specification that may be in excess of,
butnotcontraryto,thereferencedstandard.
1.6 BUILDINGSERVICEOUTAGES
A. ServiceOutageRequest:Thecontractorshallrequestallbuildingserviceoutagesthrough
the owner’s representative. The contractor shall provide a minimum notification of 24
hours.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-3
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
1.7 ELECTRICALREQUIREMENTSFORPLUMBINGEQUIPMENT
A. Equipment of higher electrical characteristics may be furnished provided such proposed
equipment is approved inwritingand connectingelectrical services, circuit breakers, and
conduit sizes are appropriately modified. If minimum energy ratings or efficiencies are
specified,equipmentshallcomplywithrequirements.
1.8 WELDINGREQUIREMENTS
A. Steel Support Welding: Qualify processes and operators according to AWSD1.1,
"StructuralWeldingCode--Steel."
1.9 FIRESAFETYPRECAUTIONS
A. AHotWorksPermitisrequiredforanytemporaryoperationthatinvolvesopenflamesor
produces heat and/or sparks. Such operations include, but are not limited to, brazing
cutting, grinding, soldering, thawing pipe, torch applied roofing, and welding. Before
doing any type of open flame or hot works operation, obtain a Hot Works Permit from
the customer service representative in the particular zone where the work will be
performed.
B. All grinding, cutting, brazing, sweating, or welding operations carried on in the vicinity
of, or accessible to combustible material, shall be adequately protected to make certain
thatasparkorhotslagdoesnotreachthecombustiblematerialandstartafire.
C. When it is necessary to do grinding, cutting, brazing, sweating or welding close to wood
construction in pipe shafts or other locations where combustible materials cannot be
removed or adequately protected, employ fireproof blankets and proper fire
extinguishers. Ahelpershallbestationednearbytoguardagainstsparksandfire.
D. Whenever combustible material has been exposed to molten metal or hot slag from
welding or cutting operations or spatter from electric arc, a fireguard shall be kept at the
place of the hot workfor at least one hour after completion to make sure that smoldering
firestonotstart.
E. Whenweldingorcuttinginverticalpipeshaftorflooropening,afireguardshallexamine
all floors belowthe weldingor cuttingoperation. Thefireguardshall be kept ondutyfor
atleastonehouraftercompletionofworktoguardagainstfires.
1.10 DELIVERY,STORAGE,ANDHANDLING
A. Deliver pipes and tubes with factory-applied end caps. Maintain end caps through
shipping, storage, and handling to prevent pipe end damage and to prevent entrance of
dirt,debris,andmoisture.
B. Store plastic pipes protected from direct sunlight. Support to prevent sagging and
bending.
1.11 COORDINATION
A. Arrange for pipe spaces, chases,slots, andopenings inbuildingstructure duringprogress
ofconstruction,toallowforplumbinginstallations.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-4
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
B. Coordinate installation of required supporting devices and set sleeves in poured-in-place
concreteandotherstructuralcomponentsastheyareconstructed.
C. Coordinate requirements for access panels and doors for mechanical items requiring
accessthatareconcealedbehindfinishedsurfaces. Accesspanelsanddoorsarespecified
inDivision8Section"AccessDoorsandFrames."
1.12 STARTUP/COMMISSIONING
A. The building plumbing systems shall be commissioned in accordance with the latest
edition of the ASHRAE document, “Guideline for Commissioning of Plumbing
Systems”. Documentation and testing of these systems is required in cooperation with
theCommissioningAuthority. Projectcloseoutisdependantonsuccessfulcompletionof
all commissioning procedures, documentation, and issue closure. Refer to Project
Closeout, Section 01700, for substantial completion details. Refer to Section 01810 for
detailedcommissioningrequirements.
B. For purposes of implementing this guideline, the Commissioning Authority shall be
definedasbeingamemberoftheUniversityStaff.
C. The contractor shall provide labor, material, and equipment required to facilitate the
commissioning process as well as making adjustments and modifications needed to
correctdeficienciesintheoperationoftheequipment.
D. The contractor shall submit copies of the service tickets to the commissioning authority
during the one-year correction period. This step verifies that there are no unresolved
deficiencieswiththesystem.
PART 2- PRODUCTS
2.1 MANUFACTURERS
A. In other Part2 articles where subparagraph titles below introduce lists, the following
requirementsapplyforproductselection:
1. Manufacturers: Subject to compliance with requirements, provide products by
themanufacturersspecified.
2.2 PIPE,TUBE,ANDFITTINGS
A. Refer to individual Division22 piping Sections for pipe, tube, and fitting materials and
joiningmethods.
B. PipeThreads: ASMEB1.20.1forfactory-threadedpipeandpipefittings.
2.3 JOININGMATERIALS
A. Refer to individual Division22 piping Sections for special joining materials not listed
below.
B. Pipe-Flange Gasket Materials: Suitable for chemical and thermal conditions of piping
systemcontents.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-5
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
1. ASMEB16.21, nonmetallic, flat, asbestos-free, 1/8-inch maximum thickness
unlessthicknessorspecificmaterialisindicated.
a. Full-Face Type: For flat-face, Class125, cast-iron and cast-bronze
flanges.
b. Narrow-Face Type: For raised-face, Class250, cast-iron and steel
flanges.
2. AWWAC110, rubber, flat face, 1/8 inch thick, unless otherwise indicated; and
full-faceorringtype,unlessotherwiseindicated.
C. FlangeBoltsandNuts: ASMEB18.2.1,carbonsteel,unlessotherwiseindicated.
D. Plastic,Pipe-Flange Gasket,Bolts,andNuts: Type andmaterialrecommendedbypiping
systemmanufacturer,unlessotherwiseindicated.
E. Solder Filler Metals: ASTMB32, lead-free alloys. Include water-flushable flux
accordingtoASTMB813.
F. Brazing Filler Metals: AWSA5.8, BCuPSeries, copper-phosphorus alloys for general-
duty brazing, unless otherwise indicated; and AWSA5.8, BAg1, silver alloy for
refrigerantpiping,unlessotherwiseindicated.
G. WeldingFiller Metals: Comply with AWSD10.12 for welding materials appropriate for
wallthicknessandchemicalanalysisofsteelpipebeingwelded.
H. SolventCementsforJoiningPlasticPiping:
1. ABSPiping: ASTMD2235.
2. CPVCPiping: ASTMF493.
3. PVCPiping: ASTMD2564. IncludeprimeraccordingtoASTMF656.
4. PVCtoABSPipingTransition: ASTMD3138.
2.4 TRANSITIONFITTINGS
A. AWWA Transition Couplings: Same size as, and with pressure rating at least equal to
andwithendscompatiblewith,pipingtobejoined.
1. Manufacturers:
a. CascadeWaterworksMfg.Co.
b. DresserIndustries,Inc.;DMDDiv.
c. FordMeterBoxCompany,Incorporated(The);PipeProductsDiv.
d. JCMIndustries.
e. Smith-Blair,Inc.
f. VikingJohnson.
2. UndergroundPipingNPS1-1/2andSmaller: Manufacturedfittingorcoupling.
3. Underground Piping NPS2 and Larger: AWWAC219, metal sleeve-type
coupling.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-6
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
4. AbovegroundPressurePiping: Pipefitting.
B. Plastic-to-Metal Transition Fittings: CPVC and PVC one-piece fitting with
manufacturer's Schedule80 equivalent dimensions; one end with threaded brass insert,
andonesolvent-cement-jointend.
1. Manufacturers:
a. EslonThermoplastics.
C. Plastic-to-Metal Transition Adaptors: One-piece fitting with manufacturer's SDR11
equivalent dimensions; one end with threaded brass insert, and one solvent-cement-joint
end.
1. Manufacturers:
a. ThompsonPlastics,Inc.
D. Plastic-to-Metal Transition Unions: MSSSP-107, CPVC and PVC four-part union.
Includebrassend,solvent-cement-jointend,rubberO-ring,andunionnut.
1. Manufacturers:
a. NIBCOINC.
b. NIBCO,Inc.;ChemtrolDiv.
E. Flexible Transition Couplings for Underground Nonpressure Drainage Piping:
ASTMC1173 with elastomeric sleeve, ends same size as piping to be joined, and
corrosion-resistantmetalbandoneachend.
1. Manufacturers:
a. CascadeWaterworksMfg.Co.
b. Fernco,Inc.
c. MissionRubberCompany.
d. PlasticOddities,Inc.
2.5 DIELECTRICFITTINGS
A. Description: Combination fitting of copper alloy and ferrous materials with threaded,
solder-joint,plain,orweld-neckendconnectionsthatmatchpipingsystemmaterials.
B. InsulatingMaterial: Suitableforsystemfluid,pressure,andtemperature.
C. Dielectric Unions: Factory-fabricated, union assembly, for 250-psig minimum working
pressureat180degF.
1. Manufacturers:
a. CapitolManufacturingCo.
b. CentralPlasticsCompany.
c. Eclipse,Inc.
d. EpcoSales,Inc.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-7
METHODS (DesignDevelopment)
AKERMANHALLHANGAR BWBRProjectNo.3.2009126.00
FIRELIFESAFETYRENOVATIONS SebestaBlombergProjectNo.206618.00
e. HartIndustries,International,Inc.
f. WattsIndustries,Inc.;WaterProductsDiv.
g. ZurnIndustries,Inc.;WilkinsDiv.
D. Dielectric Flanges: Factory-fabricated,companion-flange assembly,for 150-or 300-psig
minimumworkingpressureasrequiredtosuitsystempressures.
1. Manufacturers:
a. CapitolManufacturingCo.
b. CentralPlasticsCompany.
c. EpcoSales,Inc.
d. WattsIndustries,Inc.;WaterProductsDiv.
E. Dielectric-Flange Kits: Companion-flange assemblyfor fieldassembly. Include flanges,
full-face-orring-typeneopreneorphenolicgasket,phenolicorpolyethyleneboltsleeves,
phenolicwashers,andsteelbackingwashers.
1. Manufacturers:
a. AdvanceProducts&Systems,Inc.
b. Calpico,Inc.
c. CentralPlasticsCompany.
d. PipelineSealandInsulator,Inc.
2. Separate companion flanges and steel bolts and nuts shall have 150- or 300-psig
minimumworkingpressurewhererequiredtosuitsystempressures.
F. Dielectric Couplings: Galvanized-steel coupling with inert and noncorrosive,
thermoplastic lining; threaded ends; and 300-psig minimum working pressure at 225
degF.
1. Manufacturers:
a. Calpico,Inc.
b. LochinvarCorp.
G. Dielectric Nipples: Electroplated steel nipple with inert and noncorrosive, thermoplastic
lining; plain, threaded, or grooved ends; and 300-psig minimum working pressure at 225
degF.
1. Manufacturers:
a. PerfectionCorp.
b. PrecisionPlumbingProducts,Inc.
c. SiouxChiefManufacturingCo.,Inc.
d. VictaulicCo.ofAmerica.
PLUMBINGMATERIALS& (UofMProjectNo’s.1-266-09-1477) 220500-8
METHODS (DesignDevelopment)