AU640 Part E Software E23 Alarm E23 Alarm. E23-1 INITIALIZE System Status

100 Pages·2000·0.22 MB·English

AU640 Part E Software
E23-1
E23 Alarm
Rev.0700
INITIALIZE
System Status
(1). The system has started initialization of its mechanical components. This is an advisory alarm.
WARMUP
System Status
(1). The temperature and optical systems are stabilizing. This is an advisory alarm.
User Action
None. The mode automatically changes to WARM-UP.
STANDBY
System Status
(1). The system has switched to the Stand-By mode. This is an advisory alarm.
User Action
None. The mode automatically changes to STAND-BY.
MEASURE START
System Status
(1). The system has started analysis. This is an advisory alarm.
User Action
None. The mode automatically changes to MEASURE-1.
NO MORE RACK
System Status
(1). The system has fed the last rack from the CA unit to the sample aspiration point. This is an advisory
alarm.
User Action
None, although additional racks may be added and analysis started.
The mode automatically changes to MEASURE-2.
R1 DISPENSE FINISHED
System Status
(1). R1 reagents have been dispensed for all of the tests started. This is an advisory alarm.
User Action
None. The mode automatically changes to MEASURE-3.
CUVETTE WASH AFTER MEASUREMENT START
System Status
(1). Sample analysis is complete, the system is washing the cuvettes. This is an advisory alarm.
User Action
None. The mode automatically changes to MEASURE-4.
MEASURE END PROCESS
System Status
(1). Analysis of samples is complete and cuvette washing has finished. This is an advisory alarm.
User Action
None. The system switches from a MEASURE mode to STANDBY.
MEASURE END
System Status
(1). Analysis of samples is complete and cuvette washing has finished. This is an advisory alarm.
User Action
None. The system switches from a MEASURE mode to STANDBY.
E23 Alarm. e521e23.doc E23-1
AU640 Part E Software
E23-2
E23 Alarm
Rev.0700
MOVING TO STOP
System Status
(1). An event has occurred that has interrupted system operations.
This alarm is usually followed by other alarms describing the event in more detail. This is an advisory alarm,
the system is switching to the STOP mode during analysis.
User Action
Clear this alarm and watch for any subsequent alarms. This usually indicates a hardware failure.
MOVING TO PAUSE
System Status
The system is switching to the PAUSE mode during analysis.
An advisory alarm is given.
PAUSE
System Status
The mode changes to PAUSE. An advisory alarm is given.
User Action
System operation can be continued by pressing the Start key.
STOP
System Status
The mode changes to STOP. An advisory alarm is given.
User Action
This alarm is usually triggered by a mechanical or computer error.
The cause must be determined and corrected before restarting.
SYSTEM END PROCESS
System Status
The mode changes to END. An advisory alarm is given.
Cause
End process has been selected via keyboard input. The analyzer is powering down.
W1 START
System Status
W1 operation starts. An advisory alarm is given.
W1 END
System Status
W1 operation ends. An advisory alarm is given.
W2 START
System Status
An advisory alarm is given. W2 operation starts.
W2 END
System Status
W2 operation ends. An advisory alarm is given.
PHOTCAL START
System Status
PHOTO CAL operation starts. An advisory alarm is given.
PHOTCAL END
System Status
PHOTO CAL operation ends. An advisory alarm is given.
REMOVE RACK FROM RACK FEEDER
System Status
E23 Alarm. e521e23.doc E23-2
AU640 Part E Software
E23-3
E23 Alarm
Rev.0700
2001 THE SAME SAMPLE ID ALREADY REQUISITIONED (aaaa)
System Status
(1). The same sample ID is rejected.
Cause
(1). In Bar code Analysis mode, the sample ID read (aaaa) has already been requisitioned and cannot be
processed.
The sample ID is rejected.
aaaa : Sample ID
2002 NOT ALLOWED TO DELETE SAMPLE (aaaaa)
System Status
(1). Sample is not deleted.
Cause
(1). A sample inquired by the analyzer cannot be deleted.
aaaaa : Sample ID
2003 NOT ALLOWED TO DELETE REPEAT SAMPLE (aaaa)
Cause
(1). A repeat run sample inquired by the analyzer cannot be deleted.
aaaaa : Sample No.
2004 ALREADY REQUISITIONED REPEAT SAMPLE (aaaa)
System Status
(1). The system cannot add the requisitioned repeat run sample.
Cause
(1). If an input sample number is the same as a repeat run sample number that has already been
registered in the repeat run data file, that sample number cannot be added.
aaaaa : Sample No.
2005 ALREADY MEASUREMENT STARTED (aaaaa)
System Status
(1). Unable to requisition calibration or reagent blank.
Cause
(1). The analyzer has already inquired about the requisitioned calibration sample or reagent blank sample.
aaaaa : Sample No.
2006 PRINTER NOT AVAILABLE
System Status
(1). Printer is busy.
Cause
(1). Printer cannot be used for printing a list during measure mode.
2007 Part of data is not output yet
Operation
(1). System is still under a measure mode. Analysis mode is not completed.
User Action
(1). Confirm that the printer is operational.
(2). Access the DPR STATUS screen from the SYSTEM STATUS ICON and press the function key 4 (F4)
for printer control.
Select the analysis data, which has not yet been printed.
Cause
(1). This alarm indicates that the data printout is incomplete due to errors during the real-time print.
E23 Alarm. e521e23.doc E23-3
AU640 Part E Software
E23-4
E23 Alarm
Rev.0700
2008 Ordering
System Status
System does not change modes.
User Action
Restart after analysis has been completed.
2091 R1 LOT NO. DIFFERENT FROM RB ( aa-bbbbb ) c
System Status
(1). This is an advisory alarm.
Cause
(1). The lot no. of R1 on the reagent tray is different from the lot no. used for Reagent Blank.
User Action
(1). Perform Reagent Blank measure for the new lot of reagent.
Additional Information
(1). Error detail
aa : Tray Position No.
bbbbb : Test Name
c : Type (None : Serum U : Urine X: Other)
2092 R2 LOT NO. DIFFERENT FROM RB ( aa-bbbbb ) c
System Status
(1). This is an advisory alarm.
Cause
(1). The lot no. of R2 on the reagent tray is different from the lot no. used for Reagent Blank.
User Action
(1). Perform Reagent Blank measure for the new lot of reagent.
Additional Information
(1). Error detail
aa : Tray Position No.
bbbbb : Test Name
c : Type (None : Serum U : Urine X: Other)
2093 R1 LOT NO. DIFFERENT FROM CAL ( aa-bbbbb ) c
System Status
(1). This is an advisory alarm.
Cause
(1). The lot no. of R1 on the reagent tray is different from the lot no. used for Calibration.
User Action
(1). Perform Calibration with the new lot of reagent.
Additional Information
(1). Error detail
aa : Tray Position No.
bbbbb : Test Name
c : Type (None : Serum U : Urine X: Other)
2094 R2 LOT NO. DIFFERENT FROM CAL ( aa-bbbbb ) c
System Status
(1). This is an advisory alarm.
Cause
(1). The lot no. of R2 on the reagent tray is different from the lot no. used for Calibration.
User Action
(1). Perform Calibration with the new lot of reagent.
Additional Information
(1). Error detail
aa : Tray Position No.
bbbbb : Test Name
c : Type (None : Serum U : Urine X: Other)
E23 Alarm. e521e23.doc E23-4
AU640 Part E Software
E23-5
E23 Alarm
Rev.0700
2095 R1 DIFFERENT LOT NO. ( aaaaa )
System Status
(1). This is an advisory alarm.
Cause
(1). R1 bottles for a Test on the reagent tray have different lot numbers.
User Action
(1). Replace R1 on the reagent tray so that all of R1 bottles for a Test have same Lot No.
Additional Information
(1). Error detail
aaaaa : Test Name
2096 R2 DIFFERENT LOT NO. ( aaaaa )
System Status
(1). This is an advisory alarm.
Cause
(1). R2 bottles for a Test on the reagent tray have different lot numbers.
User Action
(1). Replace R2 on the reagent tray so that all of R2 bottles for a Test have same Lot No.
Additional Information
(1). Error detail
aaaaa : Test Name
2101 REAGENT ID READ ERROR (aa,bb)
System Status
(1). The error number is 1.
(2). The reagent shot data file is being updated.
The item name is ????.
User Action
(1). Check the bar code on the reagent bottle and then perform volume check.
(2). Verify that the correct reagent has been placed in the position assigned on the reagent tray.
Additional Information
(1). When checking reagent bar code label, an incorrect reagent ID was sent by the ANL to the DPR.
aa: Refrigerator unit : R1 or R2
bb: Reagent position : 1 to 48
2102 REAGENT ID NOT DEFINED (aa,bb)
System Status
(1). The error occurs when a reagent volume check is performed.
Cause
(1). When checking reagent bar code label, the item code of the ID read at the ID reading position does not
match the code entered in the parameter menu.
User Action
Verify that the correct bar code ID has been entered in parameters. Wipe off reagent bar code ID label.
Additional Information
(1). When checking reagent bar code label, the item code of the ID read at the ID reading position does not
match the code entered in the parameter menu.
aa: Refrigerator unit : R1 or R2
bb: Reagent position : 1 to 48
E23 Alarm. e521e23.doc E23-5
AU640 Part E Software
E23-6
E23 Alarm
Rev.0700
2103 R2 REAGENT FOUND IN R1 REF.(aaaaa,bb)
System Status
(1). The error occurs when a reagent volume check is performed.
User Action
Move the R2 reagent in the specified position to the R1 refrigerator.
Perform reagent volume check.
Additional Information
(1). When performing reagent volume check, R2 reagent detected in the R1 refrigerator at the specified
reagent position.
aaaaa : Assay name
bb : Reagent position 1 to 48
2104 R1 REAGENT FOUND IN R2 REF. (aaaaa,bb)
System Status
(1). The error occurs when a reagent volume check is performed.
User Action
Move the R1 reagent in the specified position to the R2 refrigerator.
Perform reagent volume check.
Additional Information
(1). When performing reagent volume check, R1 reagent detected in the R2 refrigerator at the specified
reagent position.
aaaaa : Assay name
bb : Reagent position 1 to 48
2105 ILLEGAL REAGENT POSITION (aa,bb)
System Status
(1). This error occurs during the reagent volume check.
Cause
(1). When performing the reagent volume check, the system detected an error at a fixed reagent position.
(2). After reading the reagent bar code label, the system detected an error in one or more of the following
cases :
- The assay name is different from the preset assay name.
- The assay is not requisitioned.
User Action
(1). Verify that a properly labeled reagent vial is placed in the assigned position.
(2). Make the appropriate corrections and repeat the reagent volume check.
Additional Information
aa: Refrigerator unit : R1 or R2
bb: Reagent Position : 1 to 48
2106 ILLEGAL BOTTLE SIZE (aa,bb)
System Status
(1). There is a discrepancy between the reagent bottle specified in parameters and the reagent bottle
detected during the reagent volume check or measure mode.
(2). Bottle size for the assay in question has not been specified.
User Action
(1). Assign the reagent position number and bottle size as follows :
1). To switch to fixed setting, check fixed position.
2). Enter the reagent assay name and appropriate bottle size.
Additional Information
(1). Incorrect bottle size specification.
aa: Refrigerator unit : R1 or R2
bb: Reagent position 1-48
E23 Alarm. e521e23.doc E23-6
AU640 Part E Software
E23-7
E23 Alarm
Rev.0700
2111 NO REPLY FROM ANL (aa,bb)
System Status
(1). The system moves to the STOP mode.
User Action
(1). Power down the system and re-boot.
Contact Olympus Technical Support if problem continues to occur.
Cause
(1). The analyzer does not send a response within a specific time frame for a request from the DPR.
aa: Message No.
bb: First byte of the message
2121 ILLEGAL FLOPPY DISK
Cause
(1). The floppy disk being used is not the correct type of disk for the task requested.
User Action
Remove the floppy disk and retry using the correct type of disk.
2122 NO DATA IN FLOPPY DISK
Cause
(1). The inserted disk is not a data diskette.
(2). The inserted disk does not contain data.
User Action
(1). Verify that the proper data disk has been inserted into the floppy drive.
2123 NO AREA IN FLOPPY DISK
System Status
(1). Data saving to the floppy disk is aborted.
Cause
(1). The floppy disk does not have enough space to save data.
User Action
(1). Insert another floppy disk with sufficient space and repeat data saving.
2131 ONLINE ERROR (aa) (bbbbbbbbb - ccccc - dd)
System Status
(1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive has been designated as
"STOP", then the following will occur:
1). Text following the alarm will not be received.
2). In a case when the test requisition is received real-time, the "STOP" status is ignored at the start of the
next analysis and the test requisition will be received real-time again.
(2). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive has been designated to
"CONTINUE", the test requisition for the next sample will be received real-time.
Cause
(1). Communication error occurs when transmitting the text for test requisition or when receiving the test
requisition format.
(2). The display in the [ ] and its meaning are as follows.
aa : type of the errors
-------------------------------------------------------------------------------------------------------
01 : Device name error
02 : Framing error
03 : Over run error
04 : Parity error
05 : Time out error
06 : Receive NAK when transmitting a text
07 : BCC error when receiving a text
08 : Other communication errors
09 : Function error
10 : Unit name error
11 : Parameter error
12 : Request cancel
-------------------------------------------------------------------------------------------------------
E23 Alarm. e521e23.doc E23-7
AU640 Part E Software
E23-8
E23 Alarm
Rev.0700
bbbbbbbbb : Text having error
-------------------------------------------------------------------------------------------------------
RB : Start text for receiving the test requisition information
RE : End text for receiving the test requisition information
R_ _ _ nnnn : normal run, normal sample, sample No.
R_ _E nnnn : normal run, emergency sample, sample No.
R_ _P nnnn : normal run, STAT sample, sample No.
R_ U_ nnnn : normal run, urine sample, sample No.
R_ UE nnnn : normal run, urine emergency sample, sample No.
R_ UP nnnn : normal run, urine STAT sample, sample No.
R_ X_ nnnn : normal run, urine sample, sample No.
R_ XUE nnnn : normal run, urine emergency sample, sample No.
R_ XP nnnn : normal run, urine STAT sample, sample No.
RH _ _ nnnn : repeat run, normal sample, sample No.
RH _E nnnn : repeat run, emergency sample, sample No.
RH _P nnnn : repeat run, STAT sample, sample No.
RH U_ nnnn : repeat run, urine sample, sample No.
RH UE nnnn : repeat run, urine emergency sample, sample No.
RH UP nnnn : repeat run, urine STAT sample, sample No.
RH X_ nnnn : repeat run, other sample, sample No.
RH XE nnnn : repeat run, other emergency sample, sample No.
RH XP nnnn : repeat run, other STAT sample, sample No.
R_ _ _ xxxxxxxxxxx : normal run, normal sample, sample ID
R_ _E xxxxxxxxxxx : normal run, emergency sample, sample ID
R_ _P xxxxxxxxxxx : normal run, STAT sample, sample ID
R_ U_ xxxxxxxxxxx : normal run, urine sample, sample ID
R_ UE xxxxxxxxxxx : normal run, urine emergency sample, sample ID
R_ UP xxxxxxxxxxx : normal run, urine STAT sample, sample ID
R_ X_ xxxxxxxxxxx : normal run, other sample, sample ID
R_ XE xxxxxxxxxxx : normal run, other emergency sample, sample ID
R_ XP xxxxxxxxxxx : normal run, other STAT sample, sample ID
RH _ _ xxxxxxxxxxx : repeat run, normal sample, sample ID
RH _E xxxxxxxxxxx : repeat run, emergency sample, sample ID
RH _P xxxxxxxxxxx : repeat run, STAT sample, sample ID
RH U_ xxxxxxxxxxx : repeat run, urine sample, sample ID
RH UE xxxxxxxxxxx : repeat run, urine emergency sample, sample ID
RH UP xxxxxxxxxxx : repeat run, urine STAT sample, sample ID
RH X_ xxxxxxxxxxx : repeat run, other sample, sample ID
RH XE xxxxxxxxxxx : repeat run, other emergency sample, sample ID
RH XP xxxxxxxxxxx : repeat run, other STAT sample, sample ID
-------------------------------------------------------------------------------------------------------
ccccc : Rack number
dd : Cup position (1 to 10)
E23 Alarm. e521e23.doc E23-8
AU640 Part E Software
E23-9
E23 Alarm
Rev.0700
2132 ONLINE ERROR [ aa ] [ bbbbbbbbb ]
System Status
(1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive is designated as "STOP",
the following events can occur:
1). The text following the alarm will not be received.
2). In a case when the test requisition is received real-time, the "STOP" designation is ignored and the test
requisition will be received in real-time at the start of the next analysis.
(2). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive is designated as
"Continue", the test requisition for the next sample will be received.
Cause
(1). Communication error occurs when transmitting the text for test requisition or receiving the test
requisition format.
(2). The display in the [ ] and its meaning are as follows.
aa: type of the errors
-------------------------------------------------------------------------------------------------------
01: Device name error
02: Framing error
03: Over run error
04: Parity error
05: Time out error
06: Receive NAK when transmitting a text
07: BCC error when receiving a text
08: Other communication errors
09: Function error
10: Unit name error
11: Parameter error
12: Request cancel
-------------------------------------------------------------------------------------------------------
bbbbbbbbb : Text having error
-------------------------------------------------------------------------------------------------------
RB : Start text for receiving the test requisition information
RE : End text for receiving the test requisition information
R_ _ _ nnnn : normal run, normal sample, sample No.
R_ _E nnnn : normal run, emergency sample, sample No.
R_ _P nnnn : normal run, STAT sample, sample No.
R_ U_ nnnn : normal run, urine sample, sample No.
R_ UE nnnn : normal run, urine emergency sample, sample No.
R_ UP nnnn : normal run, urine STAT sample, sample No.
R_ X_ nnnn : normal run, other sample, sample No.
R_ XE nnnn : normal run, other emergency sample, sample No.
R_ XP nnnn : normal run, other STAT sample, sample No.
RH _ _ nnnn : repeat run, normal sample, sample No.
RH _E nnnn : repeat run, emergency sample, sample No.
RH _P nnnn : repeat run, STAT sample, sample No.
RH U_ nnnn : repeat run, urine sample, sample No.
RH UE nnnn : repeat run, urine emergency sample, sample No.
RH UP nnnn : repeat run, urine STAT sample, sample No.
RH X_ nnnn : repeat run, other sample, sample No.
RH XE nnnn : repeat run, other emergency sample, sample No.
RH XP nnnn : repeat run, other STAT sample, sample No.
E23 Alarm. e521e23.doc E23-9
AU640 Part E Software
E23-10
E23 Alarm
Rev.0700
R_ _ _ xxxxxxxxxxx : normal run, normal sample, sample ID
R_ _E xxxxxxxxxxx : normal run, emergency sample, sample ID
R_ _P xxxxxxxxxxx : normal run, STAT sample, sample ID
R_ U_ xxxxxxxxxxx : normal run, urine sample, sample ID
R_ UE xxxxxxxxxxx : normal run, urine emergency sample, sample ID
R_ UP xxxxxxxxxxx : normal run, urine STAT sample, sample ID
R_ X_ xxxxxxxxxxx : normal run, other sample, sample ID
R_ XE xxxxxxxxxxx : normal run, other emergency sample, sample ID
R_ XP xxxxxxxxxxx : normal run, other STAT sample, sample ID
RH _ _ xxxxxxxxxxx : repeat run, normal sample, sample ID
RH _E xxxxxxxxxxx : repeat run, emergency sample, sample ID
RH _P xxxxxxxxxxx : repeat run, STAT sample, sample ID
RH U_ xxxxxxxxxxx : repeat run, urine sample, sample ID
RH UE xxxxxxxxxxx : repeat run, urine emergency sample, sample ID
RH UP xxxxxxxxxxx : repeat run, urine STAT sample, sample ID
RH X_ xxxxxxxxxxx : repeat run, other sample, sample ID
RH XE xxxxxxxxxxx : repeat run, other emergency sample, sample ID
RH XP xxxxxxxxxxx : repeat run, other STAT sample, sample ID
-------------------------------------------------------------------------------------------------------
2133 ONLINE FORMAT ERROR (aaaaaa - bbbbb - cc : NO SAMPLE No.)
System Status
(1). Disregard the test requisition information text for the sample generating the alarm.
(2). Continue to receive the test requisition information text for samples following the alarm.
Cause
(1). In the Online Parameter menu, submenu setup, the T.R.I. receive is not designated as "YES" for the
necessary parameter.
(2). The display in the [ ] and its meaning are as follows.
aaaaaa : Transferred sample type and sample No.
-------------------------------------------------------------------------------------------------------
_ _ nnnn : Normal sample
_E nnnn : Emergency sample
_P nnnn : Stat sample
U_ nnnn : Urine normal sample
UE nnnn : Urine emergency sample
UP nnnn : Urine stat sample
X_ nnnn : Other normal sample
XE nnnn : Other emergency sample
XP nnnn : Other stat sample
-------------------------------------------------------------------------------------------------------
bbbbb : Transferred Rack No.
cc : Transferred Cup position (1 to 10)
E23 Alarm. e521e23.doc E23-10